收藏本站
MAX34446
PMBus Power-Supply Data Logger
CLEAR_FAULTS (03h)
The CLEAR_FAULTS command is used to clear any latched status bits that have been set. This command clears all
bits simultaneously. If the fault/warning is still present after the CLEAR_FAULTS command is executed, the status bit is
set again. This command is write-only. There is no data byte for this command.
WRITE_PROTECT (10h)
The WRITE_PROTECT command is used to provide protection against accidental changes to the device’s operating
memory. All supported commands can have their parameters read, regardless of the WRITE_PROTECT settings. Table 5
describes the WRITE_PROTECT message content.
Table 5. WRITE_PROTECT Command Byte
COMMAND BYTE
80h
40h
00h
MEANING
Disable all writes except the WRITE_PROTECT command.
Disable all writes except the WRITE_PROTECT and PAGE commands.
Enable writes for all commands (default).
Note: No fault or error is generated if the host attempts to write to a protected area.
STORE_DEFAULT_ALL (11h)
The STORE_DEFAULT_ALL command instructs the device to transfer the device configuration information to the internal
flash memory array. Not all information is stored. Only configuration data is stored, not any status, or operational data.
If an error occurs during the transfer, the CML bit is set to 1. The device is unresponsive to PMBus commands while
transferring the configuration. This command is write-only. There is no data byte for this command. After this command
is sent, another command should not be sent for at least 250ms.
RESTORE_DEFAULT_ALL (12h)
The RESTORE_DEFAULT_ALL command transfers the default configuration information from the internal flash memory
array to the user memory registers in the device. Upon a device power-on reset or device reset through the RST input
pin, this command is automatically executed by the device without PMBus action required. This command is write-only.
There is no data byte for this command. There is no data byte for this command. After this command is sent, another
command should not be sent for at least 250ms.
CAPABILITY (19h)
The CAPABILITY command is used to determine some key capabilities of the device. The CAPABILITY command is
read-only. Table 6 describes the message content.
Table 6. CAPABILITY Command Byte
BIT
7
6:5
4
3:0
DESCRIPTION
Packet-Error Checking
PMBus Speed
ALERT
Reserved
MEANING
0 = PEC not supported.
00 = Maximum supported bus speed is 100kHz.
0 = Device does not support ALERT output.
Always returns 0000.
Maxim Integrated
19
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX34561EVKIT# EVAL KIT DUAL E-FUSE 24-TQFN
MAX34565EVKIT# KIT EVAL FOR MAX34565
MAX367CWN IC SIGNAL-LINE CIRC PROT 18-SOIC
MAX4080EVKIT+ KIT EVAL FOR MAX4080
MAX4208EVKIT+ KIT EVAL FOR MAX4208
MAX4209EVKIT+ KIT EVAL FOR MAX4209
MAX4210EEVKIT EVAL KIT FOR MAX4210
MAX4273EVKIT EVAL KIT FOR MAX4273
相关代理商/技术参数
MAX3444EAPA 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EASA 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EASA+ 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EASA+T 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EASA-T 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EEPA 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EESA 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EESA+ 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube